Mac mini 2011 upgrade kit

Be sure the grommet is seated nicely in the bracket as seen in the third picture. Repeat the process for the remaining three grommets on either sides of the brackets. The bracket with all four grommets installed should look like the bracket shown in this picture. Bend the ribbon cable along the dotted lines to help the connectors remain seated in their sockets.

Bend the ribbon cable 90 degrees at the SSD connector so that it is parallel to the connector. Use the edge of the SSD connector to put a 90 degree downward bend in the cable along the first large dotted line.

OWC Memory

Hold the ribbon cable on either side of the first small dotted line and bend it up 90 degrees. Attach the cable included in the kit to your second hard drive. In our case, we are using an SSD. If your cable came with a small piece of black tape with rounded corners, you can install it over the hard drive cable connector to secure the connector to its socket on the hard drive. The piece of tape is not required and not installing it will have no adverse effects on your machine's performance. Before attaching the cable to your hard drive make sure it has been properly folded along the dotted white lines.

iFixit Store Europe | Mac Mini Dual Hard Drive Kit

This will help the cable attach and stay in-place. Use a T6 Torx screwdriver to install two of the set screws on the side of the hard drive closest to the end of the hard drive cable that attaches to the logic board. Tighten the screws until they contact the end of the threaded holes in the side of the hard drive.

They are shown correctly installed in the third picture. When inserting the hard drive, be sure to place it in its bracket cable side up with the SATA connector closest to the bulge in the bracket seen in the third picture. Push the set screws into the grommets in the bracket and install the hard drive up into its bracket as seen in the second picture. Use a T6 Torx screwdriver to install the remaining two set screws through the grommets and into the side of the hard drive. Be sure that the mounting holes line up with the threaded holes in the outer case as seen in the second picture.

OWC Mercury Electra 6G

When the logic board is installed, simply connect the second hard drive cable to the free socket on the logic board. The second hard drive cable should lay flat between the two hard drives. If the second hard drive cable is placed on top of the first, the antenna plate will not reattach, and you could damage your cable.

OWC Mercury Extreme Pro 6G

When you start up your machine, you'll see both drives are recognized by the mini. Xbench scores show that if you install hard drives in either the top or the bottom position, their speeds will remain the same. To minimize the amount of work necessary when adding an SSD to be used as your primary drive, we recommend installing the SSD like we did in this guide and leaving the stock platter drive in its original bottom position closest to the antenna plate.

Then install Lion on your SSD. I did not complete this guide. When adding second drive, be sure that the power supply cables are secured out of the way to allow drive to be seated correctly. If cables are in the way, screw holes do not quite line up with antenna plate. This should be part of the main guide, I read this after completing my fix and I wish I had read this before.

Spent about 20 mins figuring this one out. Great guide though. When re-inserting the power supply make certain the left side screw is seated in the secondary drive tray and. Tried everything to get the points home so the right. This worked the first try.


  • Recommended Upgrades?
  • mac fan page italiana facebook!
  • OWC SSD Upgrade Kits For Mac mini !
  • Introduction.
  • Installing Mac mini Mid 2011 Dual Hard Drive Kit.
  • boston market large mac and cheese calories!
  • second y axis excel mac.

This didn't go so well. I did manage to assemble everything according to the manual, but it was one! One thing I noticed is that the cable supplied to connect the second drive to the mainboard, is slightly too long. I had to bend it quite a bit so that it would line up with the connector on the mainboard, otherwise the cable would extend about 5 mm into the mainboard and not line up. I'm afraid now that I might have broken some of the wired on the adapter while bending it. Have a fix? Post them below or e-mail us!

How to watch the Galaxy S10 launch: Samsung is expected to unveil several Galaxy models Feb.

Mac Mini Mid 2011 SSD Installation

Mobile World Congress Complete coverage from the world's biggest phone show. Be respectful, keep it civil and stay on topic. We delete comments that violate our policy , which we encourage you to read. Discussion threads can be closed at any time at our discretion. Don't show this again. Computers OWC releases dual drive upgrade kit for Mac Mini Apple's Mac Mini contains a bracket for adding additional drives, but does not provide connectors or a means for installing a drive with it. The price on SSD drives have also become quite affordable.

It's been out for a while and has proven very reliable when installed. The process is a bit more difficult than RAM, but not as hard as you think.

Here is the pricing for the EVO in the last year. The amazing thing about these upgrades is that really makes a big difference in the machine. This is why used Mac minis are always so popular.


  • Mac Mini Dual Hard Drive Kit?
  • PSA: It's a pretty great time to upgrade your Mac mini.
  • Mac Mini Mid SSD Installation - Crucial?
  • Mac mini Mid 2011 Hard Drive Replacement.

So why a sweet spot? The factories are getting really good at turning out modules at a high rate so supply is plentiful.